Search found 875 matches
- Thu 11 Feb 2021 09:10
- Forum: TraceWin
- Topic: Compensation failures proceed
- Replies: 47
- Views: 15549
Re: Compensation failures proceed
Dear Bruce, No, the number of iteration mandatory depends of the alogrithm convergence. In this case, you can see in the following figure that for exemple at step=110, penalies function is not good (delta phase and energy not close to 0), so, some more iterations are needed. convergence..png When th...
- Wed 10 Feb 2021 17:27
- Forum: TraceWin
- Topic: Compensation failures proceed
- Replies: 47
- Views: 15549
Re: Compensation failures proceed
Dear bruce, A lot of things. I tried to answer some of them, expected that solve the others :D First your steady-state ddin't reach the right energy because, your number of optimization step is two low, increase to 500, the "Maximum number of iteration" in "Matching" page -> "Second step with error"...
- Tue 9 Feb 2021 15:54
- Forum: Announcements
- Topic: TraceWin release 2.16.6.5
- Replies: 0
- Views: 1166
- Mon 8 Feb 2021 16:43
- Forum: Announcements
- Topic: TraceWin release 2.16.6.4
- Replies: 0
- Views: 1287
- Mon 8 Feb 2021 16:42
- Forum: TraceWin
- Topic: 4D & 6D emittance by errors study
- Replies: 4
- Views: 2039
Re: 4D & 6D emittance by errors study
Dear Michele,
New TraceWin version available including 4D & 6D emitances in histogram charts.
Regards,
Didier
New TraceWin version available including 4D & 6D emitances in histogram charts.
Regards,
Didier
- Mon 8 Feb 2021 11:34
- Forum: TraceWin
- Topic: 4D & 6D emittance by errors study
- Replies: 4
- Views: 2039
Re: 4D & 6D emittance by errors study
Dear Michele,
Do you speak about "histogram" plots ?
Regards,
Didier
Do you speak about "histogram" plots ?
Regards,
Didier
- Mon 8 Feb 2021 10:16
- Forum: TraceWin
- Topic: Edge of dipole application in envelope mode
- Replies: 4
- Views: 2224
Re: Edge of dipole application in envelope mode
Dear shliu,
I fixed the problem in forum about the 'dat' file.
So, using your project, I find for 45° edge, the following behavoir and I found small vertical kick. And if I incease angle to 60° vertical kick become obvious.
Regards,
Didier
I fixed the problem in forum about the 'dat' file.
So, using your project, I find for 45° edge, the following behavoir and I found small vertical kick. And if I incease angle to 60° vertical kick become obvious.
Regards,
Didier
- Fri 5 Feb 2021 17:51
- Forum: TraceWin
- Topic: Beam phase advance calculation
- Replies: 3
- Views: 1920
Re: Beam phase advance calculation
Dear Pallavi, (1) I fixed a issue in phase advance calculation in your specific conditions (Tracking with space-charge, very long structure and high transverse divergences with CW beam). Please upgrade your code. (2) I'm not sure to understand your question, but in manual you can find the phase adva...
- Fri 5 Feb 2021 17:45
- Forum: Announcements
- Topic: TraceWin release 2.16.6.3
- Replies: 0
- Views: 1336
- Fri 5 Feb 2021 11:41
- Forum: TraceWin
- Topic: Edge of dipole application in envelope mode
- Replies: 4
- Views: 2224
Re: Edge of dipole application in envelope mode
Dear shliu,
On my side I see kick in both planes, but I didn't have your project configuration. Please send me your project files (*.ini, *dat), otherwise complicated for me to check your case.
Regards,
Didier
On my side I see kick in both planes, but I didn't have your project configuration. Please send me your project files (*.ini, *dat), otherwise complicated for me to check your case.
Regards,
Didier